What's the best way to add an interior wall to an existing structure?

While you're working, be sure to take ordinary safety precautions. Wear goggles and ear protection when needed. Get help lifting.

Start by marking precisely where you want your wall. Measure to make sure each end of the wall is the same distance from a parallel wall. At each of these points, place a carpenter's square against the existing wall at ceiling height and draw a line out a few inches at a right angle to the existing wall along the line where you want the edge of the new wall to be. Tap a nail into each of these lines. Stretch a chalked string between the nails and snap it to make a line. This will be the top edge of the new wall.

Now drop a plumb line -- a string with a weight on the end -- from each nail. Mark the spots directly below the top line. Snap another chalk line between these points. This marks the bottom of the wall. Attaching the wall to the floor will be easy. You can attach it directly to almostany kind of flooringexceptcarpet．

If the plasterboard has been removed, use a level to find out if the existing walls, floor and ceiling are square. If so, you can make life easier by building your new wall on the floor. First, cut two plates, the boards that will form the top and bottom of the wall, from 2-by-4s. They will run the entire length of the new wall. Lay them side by side. Mark the locations of the studs on both plates. There will be one at each end. The rest should be separated by 16 inches (41 centimeters) [source:Gibson].

Measure the height of the room, and then subtract the combined thickness of the two plates. This will determine the length of your studs. Cut the studs, place them between the top and bottom plates, and attach them with 3.5-inch (9-centimeter) nails or screws.

With a helper, lift the wall into place. Line it up with the lines you made on floor and ceiling. "Sometimes people set the bottom along the line, then push the top into place," says Donald Holmes, a Milan, New York-based contractor. "But it's often easier to line up the top of the wall, then tap the bottom into place using a sledge hammer and a piece of scrap wood to protect the plate."

Apply a level to make sure the wall is exactly vertical. Shim any gaps between the new wall and the ceiling. Nail or screw the wall to the floor and to the ceiling joists. If the new wall aligns with a stud on the adjoining wall, attach it there as well.

Your wall is up and ready for finishing. But what if you're working in a space that's finished or where the walls are not exactly square? Then you'll want to build the wall in place. We'll talk about that method in the next section.

Building a wall in place usually makes sense when the ceiling you're working with is covered with plasterboard. You won't damage the ceiling by forcing the pre-built wall against it. This method of adding an interior wall also makes it easier to adapt to existing walls, floors and ceilings that aren't quite square.

You'll begin by marking the position of the new wall as described in the last section. Cut your bottom and top plates and mark the position of the studs. Have a helper hold the top plate against the ceiling while you nail or screw into ceiling joists along the line. Attach the bottom plate to the floor directly below the top plate.

Measure the distance between the two plates. If the floor or ceiling is uneven, be sure to measure the exact distance at every stud. Cut each stud so that it fits snugly between the two plates. First, insert the studs at either end of the new wall. Correct positioning of the two plates should make them vertical, but use a level to make sure. You'll have to toe-nail (nail at a 45-degree angle) or screw the studs to the plate. Connect them with the studs in the existing wall if you can (your stud finder will tell you where they are). Continue attaching the rest of the studs in the same way. Metal stud-framing clips, which let you nail straight into both stud and plate, are an alternative to toe-nailing [source:Holmes].

Whichever method you've used to put the wall up, it's time for finishing. Measure 4 feet (1.2 meters) from the floor at each end. Snap a chalk line across all the studs. Install cross studs snugly between the end studs at this level. "They give your wall some extra support in case someone bangs into it," says contractor Donald Holmes. "And they provide a place to attach your plasterboard."

You'll finish the project by attaching sheets of plasterboard to each side of the new wall with nails or screws. Then you'll apply plaster-like joint compound and paper tape to each joint and corner.Sandingandpaintingare the final steps. Voila: where you had one room, now you have two.

我做了一个公平bit of building to fix up my own home, including putting up interior walls. Working with an older house always presents challenges. Nothing is exactly square and you don't know what kind of surprises lurk behind the walls.

One method that has often saved my bacon is to use a cordless drill driver and screws for framing instead of a hammer and nails. Self-starting screws are easy to put in place and hold tightly. Best of all, you can easily remove them if you make a mistake. And guess what -- all do-it-yourselfers make mistakes. An added bonus: The method doesn't put the same stress on your elbow as swinging a hammer.

Related Articles

Sources